"oui mais pas un brick de la console" ==> désolé j'ai pas compris ce que tu as voulu dire ...
un brick tu as plusieurs sortes, YLOD, et GLOD, quand tu as la console qui démarre, tu as la led verte mais aucune activité du DD, ni d'image à l'écran, même pas de message d'erreur, et aucun accès au recovery, c'est un GLOD, et cela est résultant (pour généraliser) d'une impossibilité d'accès aux données de démarrage sur NOR/NAND, et cela peut venir de plusieurs causes différentes, parmi les quels :
- SB HS
- NOR/NAND HS
- Tristate activé
- 3,3V absente ou perturbée sur l'alim du NOR/NAND
.....
"le contrôleur des tensions coupe la PS3 quand ça arrive" == > mais encore, peux tu être plus précis et donner exactement ce qui est fait ...
le contrôleur de tension existe sur Xbox et sur PS3, son rôle c'est d'éviter qu'un périphérique interne ou externe (DD, manette ...) provoque un court circuit sur les lignes d'alimentation (3,3v,5v...), donc dès que ces tensions chutent suite à une demande trop forte de courant, le contrôleur coupe la PS3.
personnellement j'ai jamais vérifié, mais normalement si tu perturbe les tensions qui alimentes le DD, la PS3 coupe automatiquement, ce qui n'est pas notre cas, vue que la console continue à fonctionner donc c'est peu probable que ça vient de là
Concernant le time out, je pense que tu as raison mais j'ai jamais attendu très longtemps donc je ne pourrai me prononcer.
ben justement il faut attendre, tu finira par avoir un message d'erreur, si le problème vient du disque dur, au pire tu peux tester en débranchant ce DD, et tu aura le message de toute façon, mais si tu as un brick de type GLOD, ce message n'arrivera jamais, même DD débranché.
D'ailleurs j'en profite, aurais tu une idée sur mon pb BSOD ?
personnellement j'ai jamais croisé ce souci, mais en lisant un peu sur le net, il semble que c'est un souci en lien avec le disque dur, voila un truc à tester :
The first step is to remove the PS3 hard disk from the console.
-The next step is to connect the drive to the PC. To do this, you must turn off the PC and open the case. If you do not have any free ports or SATA cables, you can usually use the data and power cables from your DVD drive. If you have a laptop, you can get USB converters cheaply online.
-Once the PS3 hard drive is installed in the PC, start the system.
-Once windows has started, you want to open up the command prompt as Administrator.
-Type "diskpart" into the command prompt and hit ENTER.
-Type "list disk" into the command prompt and hit ENTER.
-This will produce a list of all your hard drives. You can usually identify the drive by size. You will need the disk number for the next step.
-Type "select disk X" where "X" is replaced with the drive disk number, then hit ENTER
-Type "clean" and hit ENTER.
-Type "create partition primary" and hit ENTER
-Type "select partition 1" and hit ENTER
-Type "active" and hit ENTER
-Type "assign" and hit ENTER
-At this point, windows will probably give you a pop-up offering to format the drive. It is generally a good idea to format the drive at this point just to make sure that it does not have any massive physical problems. You will want to to a "Full Format", not a "Quick Format".
-Type "exit" into the command prompt and hit ENTER
-Type "exit" into the command prompt and hit ENTER
Once these steps are done, turn off the PC, remove the drive, reconnect your DVD drive if you disconnected it, and then slide the hard disk back into the PS3.
-Now you will have to format a USB drive with FAT32.
-Create a new folder on the drive called, "PS3" (all caps).
-Open this folder and create a new folder inside of it called "UPDATE" (all caps).
-Find the PUP for whatever firmware you were running before your issues and copy it to the "UPDATE" folder.
-Rename the PUP file to "PS3UPDAT.PUP" (all caps).
-Remove the flash drive from the PC and plug it into the PS3. Plug a controller into the PS3 as well.
-Start the system and follow the prompts, if there are no hardware issues and there is nothing wrong with your USB drive, then the system should reinstall itself, often fixing multiple problems.
mais si ça marche toujours pas, essayes de remplacer le DD pour voir, si le problème persiste, dans ce cas la, le souci est plus grave, il peut venir d'un périphérique interne (NOR, Chipset sans fil, chipset réseau ...) qui fonctionne mal
Modifié par Manethon, 06 novembre 2013 - 22:27.