Télécharger Reset Glitch Hack Xenon

La Team Xecuter rend aujourd'hui possible la réalisation du Reset Glitch Hack (initialement réalisé par GliGli & Tiros)  sur les Xbox Xenon avec un deashboard inférieur à 14717/9. Attention cependant, la version Xenon du Reset Glitch Hack est capricieux et ne convient donc pas pour une utilisation de tous les jours, considérer donc cette version uniquement utile pour récupérer vos clés ou KV non banni.

Pour pouvoir réaliser ce hack, vous trouverez dans l'archive les diagrammes pour le coolrunner ainsi que les fichiers JED/XSVF. Pour la création du fichier ECC, il vous faudra utiliser le J-runner puisque la Team n'a pas releasé le build.py pour ceux ne souhaitant pas utiliser de GUI (ou un autre que le Jrunner), ce qui est d'autant plus dommage pour ce hack qui était open source à la base...

Vous trouverez

Voici le message et les explications de la Team

Wiring

Generate your ecc image using the latest version of J-Runner and flash to your NAND (+w16 just like a regular RGH).

Program your TX CoolRunner (or whatever flavor RGH mod you are using) with the tx-xenon.xsvf or tx-xenon.jed file.

The Xenon has a capacitor on CPU_RST that was removed in later  models.  C7R112 (located near the xclamp under the CPU) must be  de-soldered, and the CPU_RST wire from the TX CoolRunner(D) must be  soldered to the left pad (non grounded pad).

A 47nf ( 0.047uf) capacitor needs to be added between PLL_BYPASS(+)  and GND(-).  (If you have a genuine TX CoolRunner REV B you can use the  on-board by bridging the CAP jumper)

A 220-270pf capacitor should be added between CPU_RST(+) and GND(-)  on the cpld. (If you have a genuine TX CoolRunner REV B this is already  included in the design so not required)

An easy to follow picture guide can be found here:  http://www.team-xecu.../phat_xenon.jpg

Troubleshooting

Using a TX CoolRunner Rev B, and after applying various  troubleshooting measures we have had glitches ranging from instant to 20  minutes.

The debug LED should flash on for less than a second and repeat every  5 seconds.  If your LED stays on or does not come on at all, it is  usually because of something being wrong with PLL_BYPASS.  Try different  values of capacitors and wires. If you have enabled the CAP on REV B of  the TX CoolRunner, simply un-bridge it and try a 47nF cap instead as  per the instructions above.

If it still has not glitched after several hours, try different  values of capacitors on CPU_RST of your RGH mod.  A longer wire /  low-loss 50 ohm double shielded cable may also help with this.

To help increase boot times and stability (on all RGH installs not  just Xenon) we recommend that you try Low-Loss Double Shielded 50 ohm  cable. It's very cheap to use and quite effective – so a quick shout out  to www.xconsoles.com who supplied a batch of high quality cable for our development team to use. It's less than 75 cents a foot – not bad.

NOTE: Remember when programming the TX CoolRunner that the Xbox power  is NOT connected and that the switch is set to PRG before you connect  the JTAG cable. If you connect the JTAG cable and it is set to NOR with  the Xbox power connected, it can damage your NAND-X and/or CoolRunner.  When you have finished programming, switch it back to NOR and then power  on the Xbox.

The Xenon Hack

Please note that this hack is not available on consoles updated to dashboards 14717 or 14719.

If you are seeing the debug led it means that the cpu is probably not  crashing and the issue addressed by gligli/tiros has been fixed (This  can of course be a false positive as sometimes the CPU could be crashing  but the SMC restarts fine – we can never be 100% sure)

So far, this is really only useful for a one time cpu_key dump. There  will undoubtedly be ways of optimizing this hack in the future and who  knows, it may become a reliable glitch one day.

We would appreciate that you give as much feedback to our support forumsas  possible to help others achieve better results and to improve this  method. For now we can leave this and go back to RGH2.0 for Zephyr,  Falcon, Jasper and also of course, the Corona.

TX CoolRunner Support Forums: http://www.team-xecu...splay.php?f=174

Enjoy!

Xbox 360 Xenon RGH Hack brought to you by the Xecuter RGH Development Team

www.team-xecuter.com

Thanks

Thanks are extended to Tiros & Gligli, without your work none of this would have been possible.

A special thanks goes out to cOz – your work on Dashlaunch proved to  be an invaluable contribution and we look froward to your next exciting  project.

Greets: Team Jungle, Team FSD, Freeboot, Libxenon & RGLoader.